Used for connecting hose to valve, seacocks, strainers or any hardware having female NPT pipe threads. FF fittings are designed to accommodate the designed full pipe size flow and to provide an unrestricted passage through the fitting. Fittings are cast bronze. A hex nut is cast-in to allow for secure tightening....

Includes locknut. Bronze....

Kits includes 037-075-8 Seals (4), HF-28 Bridge, HC-5 Check Plate, HF-1 Gasket, H-27-A Joker Valve, HE-8 Gasket, HF-26 Spring.Master kit: Also includes RG-3037-A Washer (4), HF-10 Piston Assembly and H-6 Gasket....

HVL series vented loops for hose connections. The oversized vent valve is virtually clog-free, and can easily be removed without tools by unscrewing the threaded cap. Cap has 1/2\" thread for optional overboard venting. Includes mounting hardware....

Patented field reversible handle allows you to select the closed position orientation (clockwise or counterclockwise) that best suits the installation. Handle has square hole to accept standard ratchet, to help reach valves in hard-to-reach locations and ease actuation of difficult to operate valves. 400 WOG rated. Stainless steel handle and hardwa...

A pneumatic pressure charge, matched to the pump cut-on pressure prevents waterlogging by separating the air charge from system water pressure with a rubber bladder. The result is smooth pressure delivery, even temperature mix in showers, and reduced pump cycling. Mounts in any position and anywhere in the cold water plumbing after the pump. May be...

Standard Flow....

Cast bronze. Straight, standard flow....

Services deck plates or strainer caps with key holes up to 7\" apart. Pins fit holes up to 5/16\"....

...

TP tail pieces are threaded with NPS (straight) female pipe thread, and are for use with GROCO SV series seacocks or with any product with straight male pipe thread....

Protect fresh water pumps from debris. White nylon strainer head and clear plastic sight glass. Glass unscrews for filter basket cleaning. Mounting bracket included....

YQ230: Safely powers a 50A, 125/250V AC boat from two 30A, 125V AC receptacles at dockside.Note: The YQ230 Adapter will only work with two 30A receptacles that are on different phases.YQ100PLUS: Safely powers a 100A, 125/250V AC boat from two 50A 125/250V AC receptacles at dockside -or- from a single 50A 125/250V AC receptacle acting as a single ad...

Lightweight surface preparation tool. Designed for high performance. Yellow polypropylene blade is tapered for flexibility. Handles are reinforced to outlast other \"disposable\" tools. One piece construction....

Features 9 cutting positions. Die cast zinc alloy construction. One heavy duty blade included....

Flush mount bracket kit....

Features a strong steel snap hook....

Features 5,500 lb. polyester webbing and vinyl covered steel hooks....

Heavy-duty double J-hooks. Designed for quick and easy adjustment. Strong 2\" nylon webbing. Break strength is 6600 lbs. loop load....

...

This electrically activated clutch pump features a bronze body with a brass insert and offers all the benefits of flexible impeller pumps with substantial flow rate and horizontally oriented ports. The electric clutch offers convenient remote activation. Equipped with mechanical clutch engagement screws in case of electrical failure. Good for pumpi...

This portable, self-priming pump features a bronze pump head. Handles hard and soft solids without clogging. Suitable for washing down decks and docks, water for ship\'s service supply, or pumping out crankcase oil. Dry self-priming up to 4.9\' with a maximum head of 40\'. Replaceable brushes, 6\' power cord and nitrile oil resistant impeller. Incl...

Self priming flexible impeller pump. Ideal for engine cooling, washdown, circulation and other general purposes. Corrosion resistant bronze bodies and stainless shafts are well suited for marine environments. Permanently lubricated ball bearings....

Provides a very versatile means of transferring fluid almost anywhere an electric drill with 1/4\" to 3/8\" chuck can be operated. Pumps up to 3-1/2 gpm, self-priming to 3\', 1/4\" diameter shaft, supplied with 3/4\" garden hose thread port adapters, connections for 1/2\" ID hose and 3/4\" GHT female threaded fittings. Size: 3-5/16\" L x 3-1/2\" W ...

Makes quick, clean and easy oil changes on-board. 14 quart container. Hose - 1/2\" ID x 48\"L. Probe - 1/4\" OD x 40\"L. Size: 15-3/8\" H x 13-1/2\" Diameter....

Consists of a robust self-priming flexible impeller pump mounted to an easy to install base and coupled to a five port manifold, factory fitted with three full flow ball valves. This system includes a pump reversing switch to pump used oil out and new oil in, the cover includes a hinged valve cover to protect them from being accidentally opened, an...

Includes 1/2\"-20 drain plug fitting, oil drain hose, cap and hose hanger clamp. Not recommended for cars with drain plugs exposed to potential road hazard damage. Once installed, future oil changes can be done either by gravity or with the use of one of the Jabsco oil changers....

This bronze body, self-priming impeller pump will produce a dry prime suction lift of about 4\' and has a maximum head of 20\'. Use for bilge pumping, livewell circulation, washdown, and general pumping applications. Cannot be run dry. Permanent magnet type motor is fully enclosed with a stainless steel shaft and complies with USCG Electrical Stand...

This bronze body, self-priming impeller pump will produce a dry prime suction lift of about 6\' and has a maximum head of 20\'. Use for bilge pumping, livewell circulation, washdown, and general pumping applications. Cannot be run dry. Permanent magnet type motor is fully enclosed with a stainless steel shaft and has adequate torque to reverse the ...

Ideal for transferring diesel fuel. Self priming to about three feet and can pump a discharge head up to twenty feet. With an integral on/off reversing switch, it is ideal for moving fuel between tanks. Pump head can be rotated in 90° increments on motor. USCG approved for ignition protection....

...

Easily converts all PAR manually operated toilets to convenient electric operation. Complete for 29090/2910 series. Existing discharge plumbing remains undisturbed for ease of installation. Inlet port fits 3/4\" hose. 10 to 12\" high, 4\" wide, 7-3/4\" deep. Fuse size 25. 24 amp draw....

Please call our Sales Department for complete spare parts stock and information.SPARE PARTS that are stock items are listed below for Jabsco bilge pumps....

Tank is intended for installation in any pumped water system controlled by a pressure switch and can serve as a storage vessel as well as a pulsation dampener. By smoothing water flow and reducing on/off switch cycling of the pump the result is quieter operation, and longer pump life. The even flow of water gives better control of hot water tempera...

A versatile, polished brass, multi-purpose hand pump. Drain, fill or top up engine and gearbox oil. Overcomes problem of hard to reach drain plugs and filler caps. Oil and corrosion resistant brass neoprene construction with up to 1-1/2 gpm output. Connection for 1/2\" ID hose. Foot adapter for 1/2\" ID hose. Two 1/2\" ID hoses, one 5/16\" probe, a...

Compact, polished brass hand pump. Ideal for small engines and gearbox oil drain. Marine engine oil drain pump with 3/4\" female garden hose fitting on suction connection for OMC and MerCruiser 3/4\" NH threaded dip-stick tube. Includes 2 feet of 1/2\" hose. Up to 1 gpm output. Small enough to fit in any tool box. Not made for pumping gasoline or o...

Marine engine oil drain pump with 3/4\" female garden hose fitting on suction connection for OMC; and MerCruiser 3/4\" NH threaded dip-stick tube. Includes 2\' of 1/2\" hose....

Provides easy attachment of flags, boat canopies, covers and curtains. Extra long reach of hook will accept grommets inset as much as 3/4\" from fabric edge....

Safe, efficient and have high volume evacuation of hazardous vapors on vessels equipped with gasoline powered engines. Satisfies requirements of USCG regulation Title 46, Chapter I, part 183, subpart K for marine ventilation when properly installed and used. BIA type accepted. Also exhausts warm air from galleys and engine rooms, ventilating steam ...

CONTINUOUS HEAVY DUTY BLOWERS have a minimum life of 10,000 hours, making them ideal for general engine room or genset enclosure ventilation. They are also well suited for general ventilation of head or galley areas and any application that requires regular extended operation. Rated at 250 CFM ....